Creative and Handcrafted

Patchwork, quilting, dressmaking, knitting and more …

Look what I’ve got! My new Bernina Aurora 440 Quilter’s Edition May 2, 2010

Finally, I did it. Since months I was lurking around the Bernina Aurora 440 QE and since last week Friday, I am a happy new owner of one. To make sure this was the machine I would be happy with, I test sewed the model twice before deciding to buy it. I made a list of all features I wanted in a machine. My list included the following:

  • adjustable presser foot pressure
  • walking foot
  • free arm
  • quilting stitches
  • very narrow blind hem stitch for invisible appliqué
  • lower feed dogs
  • Parisian hem stitch and Venetian hem stitch for fine machine sewing
  • portable (in other words the machine should be less heavy than my vintage Singer 401 Slant-O-Matic)
  • easy to use
  • lots of useful presser feet that make my life easier
  • nice buttonholes

The Bernina Aurora 440 QE has all that and much more. I am so happy I bought it. I am thrilled with the many nice decorative stitches the machine offers (and I am actually for the first time in my life considering of using one in a project) and how neatly they are stitched out. I feel a bit bad for my faithful Singer 401, because the machine sews well and smooth, she just lacks a few stitches I desperately wanted to have. She is going to become my backup machine, as I have replaced her with a newer model. It’s kind of sad, I feel a bit like a traitor. These vintage machines were built to last and work after years like the first day they left the factory. But back to my new Bernina. What I especially like about this machine is the following:

  • It has a needle threader that actually works and is easy to use.
  • A walking foot with two soles (regular and quilting sole) comes as standard with the 440 model, as well as a nice selection of feet for quilters: the 1/4 inch (6mm) patchwork foot, open toe foot, BSR (Bernina Stitch Regulator) with three different soles (open, closed, clear with guidelines). Besides these feet the normal straight stitch / reverse foot, blind hem foot and zipper foot are included.
  • The machine has a transparent slide-on table that is easy to put on and to take off. The slide-on table has markings for inches and cm which is very practical. It comes with a long plastic ruler for even seam allowances. The ruler can be taken off if not needed.
  • The Bernina offers three thread cutters: one at the side of the machine head, one for the bobbin winder and one in the bobbin area. All three are super sharp and make a clean cut – just like sharp scissors.
  • The machine is equipped with a bobbin winder that has a separate motor. This means you can fill bobbins while sewing or embroidering.
  • Adjustable presser foot pressure: I personally believe this is a basic feature and should be included even in basic models, but many machines these days lack a manually adjustable presser foot pressure.
  • FHS (Free Hand System): this is actually a simple knee lifter, a feature well known among those familiar with industrial sewing machines. There are not many home sewing machines that offer a knee lifter. You use the knee lifter to raise the presser foot and this way you don’t have to take your hands off the fabric. Very practical.
  • This machine comes equipped with a manual sewing speed adjustment. You can sew from slow to fast. I need to say that for those used to industrial sewing machines, all home sewing machines are slow, it doesn’t matter what speed. Nonetheless I like “fine-tuning” my speed sometimes when sewing delicate things or using decorative stitches.
  • A push button to lower the feed dogs: I’ve never lowered the feed dogs on any machine as fast as with the Bernina Aurora 440 QE. You only have to push the right button!
  • Stitch Memory for programming up to 90 stitches, numbers and letters. I love it.
  • The machine has a stitch selection card that can be mounted into a holder on top of the machine, so it’s always visible. You can refer to it any time and there is no need to thumb through the manual in search for a summary of all available stitches: again very practical.
  • Talking about manual: the Bernina Aurora 440 QE comes with a nice and easy understandable manual. It is spiral bound, so you can lay it flat. It is printed on very thick paper with a smooth finish.
  • I like the cold and bright sewing light. Your eyes will appreciate it.
  • For those of us whose eyes are getting older, there is a lens set available from Bernina that can be mounted on the front of the machine, above the needle. I have heard lots of positive opinions about this accessory and as my eyes are getting tired easily, I am thinking of ordering it. It is an optional accessory and not included in the standard equipment of the machine.
  • The Bernina comes with a nice padded bag for storage.
  • The foot pedal of the machine has a cord wrapper. This again is a nice little feature to make your life easier. Remember storing your machine and coiling the cable from the foot pedal around the pedal, then trying to fit it in the space between the needle and the base of your machine? These times are over for me now.
  • The machine comes with a nice accessory box that can be mounted at the back of the machine for storage. It has plastic racks for sewing feet and bobbins. You can buy those racks separately to add more to your accessory box. Everything is visible and easy accessible.
  • There is an embroidery unit available as optional accessory for this machine. I already have a separate machine for embroidery, but it is good to know that if you would like to embroider with the Bernina, you have that option.
  • I love the stitches the Bernina Aurora 440 QE offers: 31 practical stitches, over 100 decorative stitches and 31 quilt stitches.
  • The machine makes some really nice buttonholes. Making buttonholes was never so easy. They are stitched out very neat.
  • The machine has a needle up/down feature. It can be programmed to leave the needle in the up position after finishing a seam or in the down position. You can change the needle from the up to down position or vice versa in a breeze by pushing a button OR by tapping on the foot control with your heel – again a feature that those of us used to industrial sewing machines will be familiar with.
  • I like the ease of changing feet on this machine. You don’t need a screwdriver to do that. For changing the feet you only need to raise the needle and presser foot and raise the little clamping lever on the left side to disengage the foot. To attach the new presser foot you place the opening of the foot over the metal cone and press the clamping lever down to engage the foot. That’s it. It’s fast and easy.
  • Again, you don’t need a screwdriver for changing the needle on the Bernina Aurora 440 QE. There is a clamp screw that you can loosen or tighten with your hand. That is really a relief for me, so I cannot scratch the surface of my new sewing machine by  accidentally dropping the screwdriver, something I did a lot in the past.
  • Another thing I like about my new sewing machine is the large offer of sewing feet that are available for this machine as are other accessories as well. I will buy the roller foot to sew leather and vinyl in the near future, the circle stitcher and the needle punching tool. I love the many quilting and free motion embroidery feet available for this machine. There is something for every technique and every taste.
  • What I also noticed as very pleasant is that the machine doesn’t move on the table. Not one bit. To reposition the machine on your table, you need to lift it with both hands and put it down on your sewing table again. That is excellent when sewing bigger and heavier items.
  • The first time I saw the size of the bobbin, I was stunned. It is noticeably bigger than my Singer bobbins. That is very handy for quilting.
  • Another nice feature to have is the cleaning and service notification of the Bernina Aurora 440 QE. A little oil can becomes visible on the display of the machine after approximately 180,000 stitches. To point out that your machine is due for a service, a little screwdriver and a spanner will become visible in the display, after approximately 2,000,000 stitches.
  • The bobbin case from the Bernina has a “finger”. If you thread your bobbin thread through the finger, it will raise the tension on the bobbin thread without having to modify the tension. This feature works like a charm for buttonholes, decorative stitches and satin stitching.

After raving so much about the Bernina Aurora 440 QE, I might add that even though this machine is aimed for quilters, quilting a big quilt under this machine must be challenging, because of the relatively short arm. The throat opening size (the distance from the needle to the body of the machine) is 7 3/8″ or 18.7 cm, which is neither small nor big. The larger the opening, the easier it will be to manoeuvre the three layers from the quilt sandwich through the machine, but other quilters don’t seem to have any problems finishing their quilts with this machine, so I am confident. Another nice feature to have would have been a warning in the display when you run low on bobbin thread. I know this feature is reserved for mostly the high-end embroidery machines, but quilters would appreciate this feature too, I am sure. That is all I can say for now. I am looking forward to keep you all posted about the features I discover and my experiences with my new Bernina Aurora 440 Quilters Edition.

Here a few photos from my new treasure:

My new Bernina Aurora 440 QE still in its original box.

My new Bernina Aurora 440 QE on my sewing table

The front side of the stitch card selector.

The back side of the stitch card selector.

The Bernina Aurora 440 QE accessory box.

The Bernina Stitch Regulator (BSR), unused, still in its original box.

The BSR with its three different soles: open, closed and clear with guide lines.

The Bernina walking foot with left and right guide and two soles.

The Bernina walking foot in all its glory

The Bernina walking foot in all its glory

Two soles for the Bernina walking foot: left the sole for regular sewing, right the sole for quilting.

Adjustable presser foot pressure.

The slide-on table for the Bernina Aurora 440 QE has markings for inches and cm.

The Bernina Aurora 440 QE adjustable speed control slider.

The Bernina Aurora 440 QE bobbin case, threaded through the finger.

The Bernina bobbins are slightly wider than my Singer bobbins.


10 Responses to “Look what I’ve got! My new Bernina Aurora 440 Quilter’s Edition”

  1. Adele Says:

    Oh, she is truly beautiful! As I read your blurb about your new machine I actually got very teary… Me thinks I need to get me one of those.

  2. Nelly Says:

    Thanks, Adele. I love my new Bernina!

    Time flies. I have the machine for more than a month now and in that time I tried out all stitches, different threads etc. It is so exciting. The last two days I have been washing and pressing fabrics I want to use in a quilt, so my new machine will be swamped with work from tomorrow on.

    It’s a shame how much we have to wash, press and cut, before we can sit down and do what we like most: to sew.

  3. rachal m Says:

    hope to see her at the next meeting. i love mine too!

  4. Barb Says:

    I am thinking of buying one can you tell me if you are still happy with yours.
    I figure you would definitely know by now. I bought a 2000.00 Pfaff a few years ago and it is a headache to use. I have heard that from more than one person too. I have a Bernina I have had for 20 years and still use since the Pfaff is so disappointing. I need to be sure about buying another machine and need opinions from people who have one. Thanks.

  5. Nelly Says:

    Hello Barb,

    I love my machine. It is the best I’ve ever bought. What I especially like about this machine is that it is sturdy, reliable, precise and offers a wide range of useful accessories that you can chose to buy or not. You don’t need everything, but lots of feet or accessory make your life easier.

    The Bernina has a very nice and regular stitch and it is easy to use. It gives you a lot of options. In the meantime I’ve used the BSR and I loved it.

    I am about to release a few postings about accessories I bought for my machine and I am also behind with updates about the projects I am working on. So stay tuned. There is a lot more to discover!

    In any case I would recommend you to test sew the machine before you decide to buy it. Just because I like it, doesn’t mean someone else has to.

    If you have more questions or if you do need more specific information about the machine, don’t hesitate to ask.

  6. Nima Says:

    Good to read this review..i’m looking out for an upgrade for my sewing machine and this infos about bernina was very useful. Have you tried embroidery on this machine. I’m not an hardcore machine embroider, but i would like to know, say…if i need to do few strawberries on a table cloth, will this machine able to do it…
    Looking forward to hear from you. thank you

  7. Nelly Says:

    Hi Nima,

    Thank you for your comment. I have the embroidery module for the Bernina Aurora 440 and I am very satisfied with the results. What I like most, besides the stitch quality, is that you can adjust the embroidery speed, which means that even designs with a high stitch density will be stitched out nice and neatly. The hoops are very easy to change because they use clamps instead of screws to attach the hoops to the embroidery unit. It will save you a lot of time! I know what I am talking about, my first embroidery machine was a Singer Futura CE-200 and this machine uses two screws to attach the hoops to the embroidery unit. If you have to hoop and re-hoop a few times, it can get annoying.

    All hoops from Bermina come with a plastic template that help you centre the embroidery design. Calibrating the hoop is done in a breeze with the delivered software. It will allow you, with the help of the plastic templates, to centre the needle inside the hoop accurately and quickly. This way all your designs will be stitched out in the right place.

    My first embroidery machine was a Singer Quantum Futura CE-200 and while this machine is terrific for starters, I do appreciate the operating comfort the Bernina provides me with. The sewing head of the Singer Futura is quite clunky in comparison to the Bernina Aurora, which has a negative effect on the visibility of the needle area. That was the reason why I never used the Singer Futura machine for sewing. I couldn’t see what was going on under the needle properly without crouching down in front of the machine. Since I use the Bernina, these problems are history. The Bernina delivers superb results in my opinion. I will see if I can upload a few pictures of some embroidery so you can judge by yourself. I have only ever embroidered with either the Singer Futura or the Bernina Aurora, so I cannot compare the results or ease of use to other machines which are also popular among machine embroiderers. Some popular brands include Brother, Janome, Husqvarna, Pfaff, or Babylock.

    I would expect all embroidery machines on the market today to deliver similar results. What distinguishes them besides the size of the embroider field is probably mostly the ease of use. The more sophisticated the machine, the higher the price. The only feature I believe to make a difference in regards to quality is the speed control. It can really make a difference to embroider over a “difficult” part of the design slowly instead of quickly.

    Bernina offers workbooks that help you familiarise yourself with the embroidery module and software. You can download them from various Bernina dealer websites, just search Google for workbook bernina embroidery module pdf download.

    If I was to advise you, I would tell you to search Google and Yahoo groups and internet forums for the machines that interest you. This way you will find discussions about potential problems you can encounter when working with a particular model or machine. In the end it all boils down to personal preference and budget.

    If you have any further questions, please do not hesitate to contact me. I am happy to help.

  8. joycelyn anderson Says:

    I have a aurora QE 440 edition but how do I use the stitch regulator ? there is no place to hook it up.I want to quilt a quilt .

  9. Bob Says:

    Hi Jocelyn,
    There is a receptacle for the BSR cable/plug next to cool light(area above the needle). You will have to either tilt machine or get in a good position to look up in that area. You will see a green square with a hole. Plug in BSR. You should be able to plug it in without actually seeing the hole. Plug is a “blind mate” style. Guides the plug in without having to look(by feel).
    Good Luck.

  10. Pikipiki Says:

    This post saved me! I’ve somehow misplaced the stitch card for my Bernina 440 QE and I have to finish a project with more fancy stitches. Your images of both sides of the card are a life saver. I love this machine and never feel the need to upgrade. Is it mad to love it even more for such a basic thing good bobbin winding? Among other things of course.

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s


Get every new post delivered to your Inbox.